[Cycle Concepts]

Cycle Concepts in South Carolina has engine packages for the ZX9's...big bore kit, ported head, competition valve job, adjustable cam sprockets, oversized stainless intake valves, springs and ti retainers all for $ 3095.00 out the door ready to ride...there also are less expensive packages available...please call for details...high lift cams are also available from muzzys at an additional cost....





dwayne/phil

cycle concepts

803.285.8093

</p>

 

[Cycle Concepts]

Easyrider, the few that we have built were for serious street racers in this area and we were asked not to publicize the engine combinations or hp output due to the fear of it getting out to their competition...But i will tell you this, we have gotten 180-185hp out of the 9R's....





dwayne/phil

cycle concepts

803.285.8093

</p>Edited by: <A HREF=http://pub56.ezboard.com/bkawasakizx12r.showLocalUserPublicProfile?login=bbwatercool>bbwatercool</A> at: 1/1/02 1:07:54 pm

 

[easyrider]

do you have any before and after dyno charts to show the improvement?

[email protected]
 
www.ZX-12R.org</font>
 
Top 100 Bike Sites</font></p>

 

[Guest]

Does your kit consist of a muzzy 998 kit?? I am very curious to hear some results from people that have put in these kits.



Thanks,

aaiq

</p>

 

[Cycle Concepts]

sorry we haven't done any of the muzzy stuff with the zx9's but their kits are available thru us...



dwayne

Cycle Concepts Racing
1638 Lynwood Dr
Lancaster,SC 29720
803.285.8093</p>

 

[Moto24]

I've done the Muzzy kit, I don't have dyno #'s yet but from seat of the pants it is a huge diffrence. Torque is amazing compared to stock and thats saying alot. I've done a little cleaning up of the intake ports but I have more work in that area but was limited by time. I've degreed the cams, rejetted and using the Muzzy full Ti exhaust with Ti can. It cost me about $2500.00.



What size is that kit Cycle Concepts has and is it available for the '98-'99 since it uses a diffrent cylinder?

</p>

 

[Guest]

cycle concepts,

have you guys done any heads with the intake floors raised (epoxy) how big did you make the choke if you did.

</p>

 

[Cycle Concepts]

we offer(recommend) the option of putting epoxy in the floor of the port....on the short side radius we usually have about 65% but cross sectional area is the most important number to be concerned about....



we use the stock cylinder and JE pistons on all our engine packages...



thanks,

dwayne

Cycle Concepts Racing
1638 Lynwood Dr
Lancaster,SC 29720
803.285.8093</p>

 

[Guest]

dwayne,

how much ($) to put in the epoxy in the floor of my cyl head, if i sent it to you totally diss.



thanks,

greg

</p>

 

[Cycle Concepts]

basic street port job without the expoxy starts at $500 and with the epoxy $700...let us know if we can help you...



thanks,

dwayne

Cycle Concepts Racing
1638 Lynwood Dr
Lancaster,SC 29720
803.285.8093</p>

 

[mach111]

My friend is in the middle of putting muzzy's kit in.he has a 2000.he's a certified perf.mechanic and does dam good work,knows what he's doing.he also knows alot of little mods on this bike he has come up with,dam thing was fast as shit to begin with.should be done in the next week or two,will keep posted.

</p>

 

[mach111]

update:all engine block work is done,final stages in effect tomorrow.

</p>